Ambient Weather F007TP 8-Channel Wireless Thermometer with Wet Temperature Probe

1. Replace the batteries. We recommend the following batteries:
   My Rechargeable Batteries No Longer Work. Which Batteries Are Recommended For My Weather Station?
2. Clean any corrosion around and on the battery terminals.
3. If the problem persists, the sensor array must be replaced. We have a one year warranty. To replace under warranty, please visit:www.AmbientWeather.com/rma.html
4. If out of warranty, a replacement array can be purchased at AmbientWeather.com

If the sensor displays “OF” and the console displays “LL”or “HH.H”, the senor must be replaced.

We have a one year warranty. For details, please visit: www.AmbientWeather.com/rma.html

Out of warranty replacements are available here:

F007PF:  https://www.ambientweather.com/amf007pf.html

F007T: https://www.ambientweather.com/amf007t.html

F007TH: https://www.ambientweather.com/amf007th.html

F007TP: https://www.ambientweather.com/amf007tp.html

The low voltage icon or indicator will be present on the console next to the sensor reading if the voltage falls below 2.4 Volts.

If you own more than one sensor, make sure the first sensor is on Channel 1 and the second sensor is on Channel 2.

To set the dip switches, please reference:

How Do I Set The Channel Number Using The Dip Switches In The Sensor?

Next, place all remote sensors about 10′ from the console, and then power down and up the display console. Do not touch any buttons for several minutes, until the search icon  on the display turns off.

If the problem persists, change the channel 2 sensor to channel 1 and visa versa (switch both sensor channels) and repeat the process above. Does the problem follow the sensor, or does it remain on channel 2?

If the sensor problem remains on Channel 2, the console will need to be replaced.

If the sensor problem moves to Channel 1, the sensor will need to be replaced.

We have a one year warranty. To replace under warranty, please visit:

www.AmbientWeather.com/rma.html

If the temperature reads 88.8 and Channel 8, the sensor did not completely boot up. This is because during initial power up, all of the segments are illuminated.

Remove and reinsert the batteries. If you own the F007PF Floating Pool and Spa Thermometer, press the reset button on the inside lid.

0F.L indicates there is a problem with the sensor and must be replaced. This can occur if the probe is pinched or pulled, resulting in an open circuit.

To replace under warranty, please visit: www.AmbientWeather.com/rma.html

If out of warranty, the sensor can be replaced here:

F007TP: https://www.ambientweather.com/amf007tp.html

F007TH: https://www.ambientweather.com/amf007th.html

F007T: https://www.ambientweather.com/amf007t.html

Floating Pool & Spa Thermometer loses reception

1. Sensor placement is important, since the wireless signal cannot pass through Earth or ground.  Tethering the sensor to the side of the pool that is line of sight to the sensor is recommended:
   
2. Keep the console away from any electronic radiating sources, like phones, TVs and computers.
3. If the sensor(s) have stopped communicating to your console,  it may be as simple as placing the remote(s) (powered up) about 10 feet away from the console, power down and up the console by removing one or more batteries, disconnecting from AC power (if applicable), wait 30 seconds, and put the batteries back in, then wait several minutes to resync. DO NOT TOUCH ANY BUTTONS and look for the search icon. Wait until the search icon turns off before pressing any buttons.If you have more than one sensor, make sure they are programmed to transmit on different channels.
4.  Here are some general guides on interferance:
   wireless-signal-is-intermittant-or-not-working
   
5. Still no communication press the reset button on the inside of the lid:
6. If the problem persists, we have a one year warranty:
   www.AmbientWeather.com/rma.html To replace out of warranty:F007PF:  https://www.amazon.com/Ambient-Weather-F007PF-8-Channel-Wireless/dp/B00EYGJ1KQ/ref=sr_1_1?

To set the channel number on your sensor, open the battery compartment and locate the dip switches:

For the floating pool and spa thermometer, it is on the inner lid.

Next, set the dip switches according to the table below:

For example, if you wish to set Channel 2, the first three dip switches are set to DOWN DOWN UP.

If you wish to set Channel 3, the first three dip switches are set to DOWN UP DOWN.

If the batteries have already been inserted into the sensor, you must power it down and up again by removing and inserting the batteries again.

The channel number will now be displayed on the LCD Screen (#3 below). For the F008PF, since it does not have an LCD display, will flash the channel number.

If the probe thermometer is placed in water or air, remove it from the water and compare the temperature in a controlled environment (like inside your house) and compare with a red spirit thermometer.

Mercury or red spirit thermometers are very accurate. Inside your house, place a red spirit thermometer next to the digital thermometer. The thermometers should agree within 2 degF.

Here is an example of a red spirit thermometer on Amazon:

https://www.amazon.com/SEOH-Thermometer-Spirit-Partial-Immersion/dp/B004LQ2I2M

They are also available in local hardware stores.

Other Useful Info:

1. If the sensor is separate, place the sensor in a shaded area on the north side of the structure to avoid direct and radiant heat.
2. If the sensor is placed in water, the body may have a temperature gradient and the sensors may be at different depths.

Product Manual
https://ambientweather.com/mwdownloads/download/link/id/594/

Product Page
https://www.ambientweather.com/amf007tp.html

Only the probe is water proof, which means it can be submersed in fluid. The housing is water resistant, which means water and rain can splash on it, but it cannot be submersed.

Product Manual
https://ambientweather.com/mwdownloads/download/link/id/594/

Product Page
https://www.ambientweather.com/amf007tp.html

It is a resistive thermal device, or RTD. The length can not be modified.

Product Manual
https://ambientweather.com/mwdownloads/download/link/id/594/

Product Page
https://www.ambientweather.com/amf007tp.html